Main navigation


Search found 7 matches

  Go to advanced search
by Unclesatan
Sun Jan 11, 2009 10:27 pm
Forum: Central Heating and Air conditioning and Ventilation Forum
Topic: Installing a Heat Miser PRT/HW
Replies: 0
Views: 2630

Installing a Heat Miser PRT/HW

Hello I bought a Heatmiser PRT/HW from recommendations on this site and thought it would be a straight swap for my invensys up2 duel channel controller, however I cant seem to make it work. I thought it would be a straight swap but the wiring is different and I was wondering if somebody could steer ...
by Unclesatan
Mon Nov 17, 2008 9:53 pm
Forum: Central Heating and Air conditioning and Ventilation Forum
Topic: I think I need a new water pump but I just want to be sure
Replies: 3
Views: 3222

Well I replaced the pump and no joy although replacing the pump wasn't a total loss as its got a much lower energy rating so when it's all working it should cost less to run. :? The boiler isn't engaging now, the On light comes on followed by the fan light, but it doesn't proceed to the pilot and bu...
by Unclesatan
Mon Nov 17, 2008 11:26 am
Forum: Central Heating and Air conditioning and Ventilation Forum
Topic: I think I need a new water pump but I just want to be sure
Replies: 3
Views: 3222

I think I need a new water pump but I just want to be sure

I have a Baxi Solo 40PF Boiler in the garage feeding a vented cylinder in the upstairs airing cupboard, the central heating is a closed system and the pressure is fine. There is also a mid position valve which appears to work as when I disconnect it and operate the valve manually there is no change....
by Unclesatan
Fri Jun 27, 2008 12:11 pm
Forum: Plumbing Forum
Topic: Converting to Direct Mains System
Replies: 8
Views: 23787

PLumbob, thanks for the info. I was under the impression I had an unvented cylinder, but It appears that I dont as my cylinder looks like the one in your link. Should a low pressure cylinder have an expansion tank? As mine has one fitted? Perry525, there are only 2 of us in the house so our water ne...
by Unclesatan
Thu Jun 26, 2008 9:22 pm
Forum: Building Regulations and Planning Permission Forum
Topic: Fire Door - Utility Room to Garage
Replies: 2
Views: 5902

Re: Fire Door - Utility Room to Garage

[quote="Tanglefoot"]... and is their any special requirement with regard to locks - mortice/yale etc? [/quote] My answer isn't to do with Building Regs, but it's something you should consider. With regards to locks ring your insurance company, if they consider you in a high risk area they ...
by Unclesatan
Thu Jun 26, 2008 10:08 am
Forum: Plumbing Forum
Topic: Converting to Direct Mains System
Replies: 8
Views: 23787

[quote="plumbbob"]the ball valves would be set for low pressure. You may have to replace them if the conversion parts are not to hand. [/quote] Thanks for your reply. The toilets have been replaced within the last couple of years so parts for them shouldn't be an issue. Is there anyway I c...
by Unclesatan
Tue Jun 24, 2008 10:15 pm
Forum: Plumbing Forum
Topic: Converting to Direct Mains System
Replies: 8
Views: 23787

Converting to Direct Mains System

Hello, this will be my first post so hello everyone. I've done a search on this but come up empty handed so please forgiveme if I've missed a previous topic. My house has an Unvented Hot water Cylinder and a lot of the cold taps seem to be mains fed, however I still have a header tank in the loft wh...
It is currently Fri Nov 22, 2024 2:35 am
Go to advanced search