Search found 3256 matches

by htg engineer
Sun Jul 21, 2019 9:43 am
Forum: Central Heating and Air conditioning and Ventilation Forum
Topic: Turn on Combi Boiler with no Radiators Attached?
Replies: 1
Views: 1718

Re: Turn on Combi Boiler with no Radiators Attached?

It depends on the boiler make and model, you need the heating side pressurised, so it's best to either leave one radiator connected, or link the flow and return at the boiler. You might be able to isolate the flow and return at the boiler, and pressurise the heating side, but you could end up causin...
by htg engineer
Sat Jul 06, 2019 7:00 am
Forum: Plumbing Forum
Topic: Electric Only Immersion Heater With Cold Tank Above in Airing Cupboard
Replies: 1
Views: 1948

Re: Electric Only Immersion Heater With Cold Tank Above in Airing Cupboard

Check the ballvalve in the tank is filling as quickly as its emptying, as the water has been off for the shower fitting, it is likely some debri has got stuck in the valve.
by htg engineer
Fri Jul 05, 2019 7:31 pm
Forum: Bathrooms, Drainage and Waste Plumbing Forum
Topic: Fitting Awkward Plumbing Bath Waste
Replies: 1
Views: 2172

Re: Fitting Awkward Plumbing Bath Waste

Bath trap and 135 bend, or last resort a short flexi waste pipe.
by htg engineer
Fri Jul 05, 2019 7:22 pm
Forum: Plumbing Forum
Topic: Bathroom Shower Mixer fed from Central Heating?
Replies: 1
Views: 1725

Re: Bathroom Shower Mixer fed from Central Heating?

The water in the radiators is not the same as what would come out of the hot tap.

You need to tee into the hot water pipework supplying the basin.
by htg engineer
Fri Jun 28, 2019 9:17 pm
Forum: Plumbing Forum
Topic: Central Heating Pipe Alteration and Routing
Replies: 1
Views: 4113

Re: Central Heating Pipe Alteration and Routing

Most manufacturers require at least the 1st metre off the boiler is copper. You don't want to restrict the flow too much, it's best to run as far as you can in 22mm and branch off for each radiator with 15mm. A short 15mm run will be okay for 2 radiators. Isolation valves are handy if hidden under f...
by htg engineer
Thu Jun 27, 2019 6:31 am
Forum: Bathrooms, Drainage and Waste Plumbing Forum
Topic: Unable to get old Toilet Seat Fittings Removed as There is Nowhere to Screw
Replies: 3
Views: 1864

Re: Unable to get old Toilet Seat Fittings Removed as There is Nowhere to Screw

The 2 silver discs will pop off and reveal the screw,.
by htg engineer
Wed Jun 26, 2019 5:05 pm
Forum: Lofts and Loft Conversions Forum
Topic: Loft Flooring Question Concerning Loft Conversion
Replies: 6
Views: 2815

Re: Loft Flooring Question Concerning Loft Conversion

Is that head height with your 50mm insulation over the rafters, plasterboard/slim.

I would just run by building control, before starting. We needed 2m on the stairs and he wouldn't pass 1.9m so had to alter them to get the height
by htg engineer
Wed Jun 26, 2019 12:16 pm
Forum: Lofts and Loft Conversions Forum
Topic: Loft Flooring Question Concerning Loft Conversion
Replies: 6
Views: 2815

Re: Loft Flooring Question Concerning Loft Conversion

I'm in the middle of doing my loft, the new joists come off the wall plate, and didn't require any steel. The new joists are above the existing ceiling joists, I've never seen a loft conversion where the old joists and ceiling were removed, unless there's is a requirement to - to get the required 2....
by htg engineer
Wed Jun 26, 2019 6:43 am
Forum: Lofts and Loft Conversions Forum
Topic: Loft Flooring Question Concerning Loft Conversion
Replies: 6
Views: 2815

Re: Loft Flooring Question Concerning Loft Conversion

The joists would normally go between the steel, over the top of the existing ceilings/joists but not in contact with them.
by htg engineer
Tue Jun 25, 2019 6:49 pm
Forum: Plumbing Forum
Topic: Finding 70mm top and 30mm Side Tube Basin Waste
Replies: 1
Views: 1772

Re: Finding 70mm top and 30mm Side Tube Basin Waste

Have a look at the Macdee vanity basin wastes.

The Macdee Wirquin is very similar.
by htg engineer
Mon Jun 24, 2019 5:55 pm
Forum: Bathrooms, Drainage and Waste Plumbing Forum
Topic: Noisy Quarter Turn tap Valves
Replies: 1
Views: 2067

Re: Noisy Quarter Turn tap Valves

Check that the taps are the right ones, meant for high or low pressure. If the hot water is tank fed, they might not be suitable for high pressure, and why you're getting the noise on the cold mains.
by htg engineer
Sun Jun 23, 2019 9:57 am
Forum: Central Heating and Air conditioning and Ventilation Forum
Topic: Yellow Tag on Valve With Baxi WM 40/3 OF
Replies: 4
Views: 1968

Re: Yellow Tag on Valve With Baxi WM 40/3 OF

I think your friend may have assumed it was gas, when you mentioned a yellow tag.

If the heating is working then yes, leave it as it is until you get sorted. There's that many safety devices on boilers now, if it didn't like what was happening, the boiler would lock out on fault.
by htg engineer
Sat Jun 22, 2019 1:19 pm
Forum: Roofing Repair and Construction Forum
Topic: Roof Issue With Neighbours Replacing Tiles With Different Tiles to Existing
Replies: 1
Views: 2882

Re: Roof Issue With Neighbours Replacing Tiles With Different Tiles to Existing

You need to get them back, both sides need to be made good, any gap letting in daylight will allow water in and cause noise when windy.
by htg engineer
Sat Jun 22, 2019 1:17 pm
Forum: Hand and Power Tools Forum
Topic: Using Rotary Sander on an Electric Drill
Replies: 2
Views: 2203

Re: Using Rotary Sander on an Electric Drill

You'll struggle to manage the speed with a drill attachment, a dremmel or similar would be better and you'll get finer tips for hard to reach grooves.

Wire wool is also good for preparing wood.
by htg engineer
Sat Jun 22, 2019 12:58 pm
Forum: Central Heating and Air conditioning and Ventilation Forum
Topic: Have I Bust my Towel Rail?
Replies: 1
Views: 1822

Re: Have I Bust my Towel Rail?

Best thing is to remove the tail, and try a new one with ptfe and paste. You may be lucky and damaged the tail thread rather than the towel rail.
It is currently Fri Oct 04, 2024 2:54 pm