DIY Doctor UK DIY Forums

chrisroberts

get a rubber glove and wrap it round the mixer tap where the water comes out, hold it tight with hand then gently open the mixer so the cold water can back flow thru the hot pipes, hold for about 30 seconds, this should blow any trapped air into your header tank.

chrisroberts

Hi, i have a heatre sadia 75 ltr hot water storage heater, im wanting to sell it. Does anyone know a site where i can advetise it that would appeal to the right people. Thanks chris.

chrisroberts

Thanks for your comments Chris, all rads are fitted with trv's so i best fit the auto bypass. Thanks again.

chrisroberts

hi, im busy fitting my own central heating pipes and radiators ready for my combi boiler. im doing a 2 pipe flow and return system and ive been told i need to fit an auto bypass valve. is this true and if so where and how is it fitted? what pressure setting and so on. any advice much appreciated. Th...

chrisroberts

Hi, i bought and fitted an immersion to my hot water cylinder that i bought from b&q 6 months ago, now the immersion has given up. the previous one was in for over 10 year.

can anyone recommend a good immersion. 27" top entry. many thanks Chris.

chrisroberts

hi, it sounds like there could be a problem with you cold water mains water pressure. that would cause a noise when re filling the toilet cistern, and also low pressure to the shower may cause the fault light to come on. check your mains stop cock is fully open then turn back a quarter turn.

chrisroberts

Hi, i would check the instructions for that particular saniflow as to how high you can pump the watse. make sure you use sweep bends for the 2 corners and all should be well.

chrisroberts

Have you fully turned the mains back on? is the cold water pressure ok else where in the house?

Maybe check the washer you have replaced, it may not been sitting right on the end of the valve.

chrisroberts

Hi there, i have an elson tank in the loft of my bungalow that supplies hot water to the kitchen and bathroom. radiators are electric so thankfully i need not worry about the heating. my immersion element has gone in the elson tank, ive tried all ways to get the element out and its not budging. sooo...

chrisroberts

i bought a shower tray not so long back and it came with a 32mm flexy pipe built in to the wate outlet. now its fitted im suffering from slow drainage in the tray. i was under the impression shower waste had to be 40mm? if so. how do these companies get away with selling them if its not fit for purp...

chrisroberts

radiator in kitchen not heating up. just had 2 new valves fitted. trv on the flow and a trv on the return. should i have a normal valve on the return side instead of a trv. are the trv's fitted with a none return valve in them. thanks.

chrisroberts

try a flexy waste from b&q

chrisroberts

i have an old length of lead pipe in the kitchen that i need to cut back and cap off. it is live mains pressure. do you have to solder it or is there a special blank off fitting, cheers chris.

chrisroberts

can anyone help, i have a easy plumb shower tray. it come with a flimsy 32mm flexy waste. how would i connect the 32mm flexy end to the 40mm pipe? thank you Chris

chrisroberts

im guessing your main cold water supply comes in the kitchen and the kitchen tap is tee'd off it then it will feed the tank in the loft, if the kitchen tap is fine then it sounds like abit of debris may have entered the float valve in the tank. check that the float is operating correctly in the tank...

Project Type A - E

Project Type F - G

Project Type G - J

Project Type M - P

Project Type R - T

Useful Tips

Search found 21 matches

Heatre sadia hw tank

fittng a automatic bypass valve to central heating system

immersion problem

replacing elson tank for new direct cylinder?

shower waste only 32mm flexy?

radiator not heating up.

old lead pipe

easyplumb shower tray waste

Main navigation

Search found 21 matches