Main navigation


Search found 44 matches

  Go to advanced search
by gasmick
Sat Apr 17, 2010 6:51 pm
Forum: Brickwork and Blockwork Forum
Topic: New External Chimney Help
Replies: 3
Views: 2776

Hi i built a chimney on the outside of my new house a few years ago and the first thing i did was to chop out a couple of course of bricks and go into the cavity i then shuttered up a 6 inch deep square box and about 2ft square and i blocked off a bit of the cavity downwards and to the sides i then ...
by gasmick
Tue Mar 17, 2009 9:24 pm
Forum: Plumbing Forum
Topic: shower in low pressure bathroom
Replies: 7
Views: 3901

The best way to do it so that its safe to use is to fix a storage tank in the roof of around 50 gall and feed the hot water to the cyld from that and also the cold feed to the shower if you can get enough head in the roof then you will not need a pump providing you use a low pressure shower mixer if...
by gasmick
Mon Mar 09, 2009 5:18 pm
Forum: Plumbing Forum
Topic: Hot water
Replies: 1
Views: 2335

hi i am very confused with your dicription of your heating and water system ? you say your heating is warm air from the 70s as you call it an old school system???? most systems with warm air were johnson a n starley, or suggs, and all were fitted with a circulator which is a gas water heater conecte...
by gasmick
Fri Mar 06, 2009 9:34 pm
Forum: Plumbing Forum
Topic: Boiler not restarting after CH reaches temperature
Replies: 3
Views: 3217

hi it sounds like the stat has gone out of callibration perhaps needs changing for a new one
by gasmick
Sun Mar 01, 2009 8:21 pm
Forum: Plumbing Forum
Topic: Black gunge from hot tap
Replies: 3
Views: 4705

hi it sounds like you have a primatic or an auto vent cyld and the seal has gone it will need replacing but primatics are few and far between to get nowdays, so it will need to be replaced with an indirect cyld with a coil internally and a seperate header tank, Under the latest regulations its a rep...
by gasmick
Thu Feb 26, 2009 8:59 pm
Forum: Plumbing Forum
Topic: New sink with pop up plug function?
Replies: 1
Views: 3249

hi the monoblock sink mixer comes as a kit with a pop up waste in the kit, or you can but a mixer tap and use a slotted waste with a plug and chain
by gasmick
Thu Feb 26, 2009 8:55 pm
Forum: Plumbing Forum
Topic: Combi -condensing boiler and my Shower?
Replies: 12
Views: 24464

hi as i have mentioned before bath shower mixers do not work properly on combi boilers i know what you are saying about pressure but the hot water flow rate on the tapas will be a lot different to the cold that is why you will need a double pressure equalizing valve fitted so the cold pressure does ...
by gasmick
Wed Feb 25, 2009 10:08 pm
Forum: Plumbing Forum
Topic: Change in shower pressure.
Replies: 2
Views: 2535

Hi have you replaced it with the same LOW pressure type as i assume your old system worked of storage tank in the roof and from the hot water cylinder, and not with one the works on a combi if its not a low pressure one that will be the cause of your problem as well, so check out what model you have...
by gasmick
Wed Feb 25, 2009 10:01 pm
Forum: Plumbing Forum
Topic: Combi -condensing boiler and my Shower?
Replies: 12
Views: 24464

Its not advisable to run a combi boiler with combination bath and shower mixers taps, as they mix in the body of the shower and could send the hot water from the comb back to the boiler as the pressures will be different on the hot an cold and that will keep shutting the boiler down,,, you can get a...
by gasmick
Wed Feb 25, 2009 9:45 pm
Forum: Gas and Gas Fitting Forum
Topic: baxi combi 80 eco firing problem
Replies: 11
Views: 27955

Hi its a problem with many forums you give advice as an engineer to a problem posted as lots of others do the same, but the original poster never seems to finnish off their posting with a problem solved post ??? at least we as engineers would know if our solution worked for them and thanks would be ...
by gasmick
Tue Feb 17, 2009 11:44 pm
Forum: Plumbing Forum
Topic: Replace Primatic with indirect cylinder
Replies: 5
Views: 6549

you have just created a time bomb so do not turn on the boiler as there is now no expansion to the system the expansion tank should go in the roof with a cold feed and an expansion pipe over the tank anyway you should not be fitting the repacement cyld yourself as it comes under the building regs no...
by gasmick
Tue Feb 17, 2009 11:34 pm
Forum: Plumbing Forum
Topic: Hot water supply inadequate and intermittent from combi
Replies: 1
Views: 2840

souds like its due for a good service and a check over with the gas working pressures etc and i should get the engineer to check the plate heat exchanger as it does sound like its getting clogged up and need descaling etc
by gasmick
Tue Feb 17, 2009 11:20 pm
Forum: Central Heating and Air conditioning and Ventilation Forum
Topic: ENERGYCATCHER
Replies: 3
Views: 3390

hi i do not know why everyone pulls ravenheat down as being a bad boilers they are no worse than a lot of other manufacturers in fact for the price i think they represent very good value I have been carrying out out of warrenty work for ravenheat for a few years now and for private customers as well...
by gasmick
Tue Feb 17, 2009 10:59 pm
Forum: Central Heating and Air conditioning and Ventilation Forum
Topic: worchester boiler
Replies: 2
Views: 2863

hi it sounds like its to do with the air pressure switch cutting out , it could also be a problem with the pipes to it as the can get perrished and while it will ignight it will keep dropping out, and then going through the same process, also it could also be a problem with the ventura if its dirty ...
by gasmick
Wed Jan 07, 2009 10:56 pm
Forum: Plumbing Forum
Topic: noisy Thermastatic valve .
Replies: 3
Views: 2326

its a common fault with some valves even reverse flow ones what you need to do is to remove the top of the lockshield valve at the other end and turn it down until its almost closed then keep opening it a bit at a time until the noise stops m y information came from the valve manufactureres as i use...
It is currently Fri Nov 22, 2024 7:36 am
Go to advanced search